Psychobike banner

Status
Not open for further replies.
1 - 6 of 6 Posts

·
Registered
Joined
·
20 Posts
Discussion Starter #1 (Edited)
2004 Turbo Hayabusa for Sale - $11,000

Steve Knecum built motor

CP Pistons

Carrillo rods

Carpenter head work

roller cam chain conversion

Clutch cylinder support

MTC Billet basket, inner hub and lockup

Robinson large output shaft trans w all size sprockets 16 to 19

Trac Dynamics swing arm

Galfer rotors and pads – all braided lines

Penske double adjustable shock

Fresh paint with factory stickers cleared over

Tuned by Mike Tona @SAE -248rwhp at 7lbs,also made 330 rwhp @ 11lbs

RCC Stainless Header

RCC quick access clutch cover

RCC oil scavenging pump

Wego Data Logger

Dump pipes and full exhaust w/custom stainless can

2 seats - 1-drag race low cut and 2- higher for more padding

rear seat and hump

turbosmart waste gate, 7lb = current, + 3lb and 5 lb springs

PC V

Boost by Smith gear counter, air shifter, w/auto option and compressor in tail

2 windscreens, stock low and tall.

carbon wheel hugger

low peg mounts on swing arm, if your tall like me w/pegs

Spare new turbo cartridge

Stock swingarm w/extenders and built in air tank

Tiger tail

Great street bike, drag race or land speed, take your pick

Probably have more parts that I cannot think of right now, email me if you are interested.

I am in CT.

[email protected]
 

Attachments

·
Registered
Joined
·
20 Posts
Discussion Starter #3
2004 Turbo Hayabusa for Sale - $11,000

Steve Knecum built motor

CP Pistons

Carrillo rods

Carpenter head work

roller cam chain conversion

Clutch cylinder support

MTC Billet clutch basket + inner hub+ 2 stage lockup

Robinson large output shaft trans with all size sprockets 16 to 19

Trac Dynamics swing arm

Galfer rotors and pads – all braided lines

Penske double adjustable shock

Fresh paint with factory stickers cleared over

Tuned by Mike Tona @SAE -248rwhp at 7lbs, also made 330 rwhp @ 11lbs

RCC Stainless Header

RCC quick access clutch cover

RCC oil scavenging pump

Wego data logger

Dump pipes and full exhaust w/custom stainless can

2 seats - 1-drag race low cut and 2- higher for more padding

hump in place of rear seat

turbosmart waste gate, 7lb = current, + 3lb and 5 lb springs

PC V

Boost by Smith gear counter, air shifter, w/auto option and compressor in tail

Tall wind screen

carbon wheel hugger

Ceramic wheel bearings

Aluminum adjustable kickstand

low peg mounts on swing arm, if your tall like me w/pegs

Tiger tail

Great street bike, drag race or land speed, take your pick

Less than 700 miles on all new motor, parts and paint.

Spare parts that are included:

Stock swingarm w/built in air tank and extenders = $250

stock rear shock = $250
850 lb Penske spring - $50
full exhaust w/custom stainless can for – value = $400

Low padded seat for racing–value = $50

Rear seat -$100
Turbo smart waste gate springs 3+5lb – $20

Stock windscreen – value = $50
Stock kickstand – value = $25
Billet Aftermarket gas cap – value = $25
Pegs for swing arm – value = $20
Spare new turbo cartridge – value = $500

Complete set of new / used clutch plates – value = $100

MTC chrome hardened steels plates – value = $50

Spare side panels used condition – value = $100

Schnitz front end tie down for drag racing - value = $10

17, 18, and 19 tooth front large shaft sprockets – Robinson – value = $300?

Tiger racing Hayabusa engine stand – value = $100

New chain to extend the wheelbase to 68in – value = $150

Roaring Toyz adjustable dog bones – value = $50

Mr gasket new exhaust turbo gaskets - value = $40

Stock / Modified by MTC clutch cover to fit lockup – value = $100

38 tooth rear sprocket for land speed racing – value = $50

Ballistic battery charger- balance cells – value $100

Converti Handle bars – value = $300


I am in CT.

[email protected]
 
1 - 6 of 6 Posts
Status
Not open for further replies.
Top