+ Reply to Thread
Results 1 to 7 of 7

suzuki SET Valve/Servo motor 01 750 help!

This is a discussion about suzuki SET Valve/Servo motor 01 750 help! within the Tuning Performance section, where you will Engine mods-Tuning talk for all Sport Bikes Every little bit helps!; Here's what i got: 01 gsxr 750. full exhaust etc. i took out the secondary butterflies, this past season, and now im doing some weight saving and that servo motors gota go. But. . .

  1. #1
    Moving up the Ladder
    TwsTdGsxR's Avatar
    Join Date
    Feb 2009
    Location
    N.J.
    Posts
    477
    Post Thanks / Like
    Real Name
    Vinny Cianci
    Rep Power
    4

    Default suzuki SET Valve/Servo motor 01 750 help!

    Here's what i got: 01 gsxr 750. full exhaust etc. i took out the secondary butterflies, this past season, and now im doing some weight saving and that servo motors gota go.

    But. . . when i unplug it its throw the ever so in your face "FI" light. the instructions i got with the TiForce pipe on the bike say nothing about cutting the wire on a 750 only on a 1000.

    a helpful psychobiker sent me some pics of the wires he had cut but the actual wiring at the ecu from the 750 and 1000 are different(he had a 1000)

    i stripped the harness to see where the wires go and my servo motor has two plugs one plug has three wires a yellow, a red, and a brown with black stripe, the other plug a red with black stripe and a black with red stripe.

    Is there and way to do this without that damn light blinking in my face? or am i going to have to deal with the light?

    and if that is the case, will it make the bike run in a limp mode or on a pre determined set of values like a OBDII car computer would or is this computer system prehistoric?

    thanks for reading and trying to help -Vin
    elbow up, rudder down. . .

  2. Remove Advertisements
    PsychoBike.com
    Advertisements
     

  3. #2
    Moving up the Ladder
    TwsTdGsxR's Avatar
    Join Date
    Feb 2009
    Location
    N.J.
    Posts
    477
    Post Thanks / Like
    Real Name
    Vinny Cianci
    Rep Power
    4

    Default Re: suzuki SET Valve/Servo motor 01 750 help!

    anybody???
    elbow up, rudder down. . .

  4. #3
    Holeshot Member

    Join Date
    May 2004
    Location
    Gretna, la to Bossier City,la
    Posts
    213
    Post Thanks / Like
    Rep Power
    8

    Default Re: suzuki SET Valve/Servo motor 01 750 help!

    I did this to a buddys bike

    take the servo motor off the bike and I can't remember which wires it was but put an ohm meter on two of the wires at a time and with the meter set on ohms check the wires till you find the two with a resistance reading, then go to radio shack or an electronic store and get a resister at that value put it on those two wires in the harness on the bike and the FI light will go off

    if you can't get it let me know and I'll see if I can get the bike to check it

  5. #4
    Moving up the Ladder
    TwsTdGsxR's Avatar
    Join Date
    Feb 2009
    Location
    N.J.
    Posts
    477
    Post Thanks / Like
    Real Name
    Vinny Cianci
    Rep Power
    4

    Default Re: suzuki SET Valve/Servo motor 01 750 help!

    ok im going to try that tonight and i'll let you know how it goes, thanks
    elbow up, rudder down. . .

  6. #5
    Moving up the Ladder

    Join Date
    Feb 2007
    Location
    Australia
    Posts
    360
    Post Thanks / Like
    Rep Power
    0

    Default Re: suzuki SET Valve/Servo motor 01 750 help!

    on my 01 1k i unplugged the 3 pin plug and bridged the 2 pin to remove the servo with no fault codes

  7. #6
    Super HoleShot Member
    ChrisBurke's Avatar
    Join Date
    Sep 2009
    Location
    Brookshire, TX
    Posts
    165
    Post Thanks / Like
    Real Name
    Chris
    Rep Power
    3

    Default Re: suzuki SET Valve/Servo motor 01 750 help!

    you have an 01 750? on my old 03 there was no SET valve to remove...im pretty sure that was only available on the 1000s

  8. #7
    Moving up the Ladder
    TwsTdGsxR's Avatar
    Join Date
    Feb 2009
    Location
    N.J.
    Posts
    477
    Post Thanks / Like
    Real Name
    Vinny Cianci
    Rep Power
    4

    Default Re: suzuki SET Valve/Servo motor 01 750 help!

    yea its a a 750 with a set valve maybe someone took it off yours, thats weird
    elbow up, rudder down. . .

Similar Threads

  1. turbo motor valve springs
    By David Annas in forum Suzuki Hayabusa
    Replies: 4
    Last Post: 01-10-2010, 12:29 PM
  2. Suzuki Hayabusa Motor
    By dakadr4 in forum Wanted Items
    Replies: 3
    Last Post: 08-21-2009, 10:41 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.