cam degree help zx10 - Page 2

+ Reply to Thread
Page 2 of 2 FirstFirst 12
Results 16 to 22 of 22
Like Tree2Likes

cam degree help zx10

This is a discussion about cam degree help zx10 within the Tuning Performance section, where you will Engine mods-Tuning talk for all Sport Bikes Every little bit helps!; Originally Posted by Gregory Clay Those numbers will kill you on the big end What #s would u go with Greg?

  1. #16
    Moving up the Ladder
    Steve 10r's Avatar
    Join Date
    Apr 2012
    Location
    Angleton, Texas
    Posts
    122
    Post Thanks / Like
    Real Name
    Stephen
    Rep Power
    3
    Country: United States

    Default

    Quote Originally Posted by Gregory Clay View Post
    Those numbers will kill you on the big end
    What #s would u go with Greg?

  2. Remove Advertisements
    PsychoBike.com
    Advertisements
     

  3. #17
    Moving up the Ladder
    gazx10's Avatar
    Join Date
    Mar 2010
    Location
    monroe, ga.
    Posts
    570
    Post Thanks / Like
    Real Name
    jim shepard
    Rep Power
    5

    Default

    just dyno'd and ran 07 10 with ported head, 08 race int. stk. ex. decked ,015, .050 hg, brock pipe, springs, retainers. very similar to u. degreed cams too high lc, 110 int., 106.5 ex., still climbing on dyno at 12500 rev limiter, soft off the line at the strip. gonna redegree to lower #'s, probably 107 int., 104-105 ex. to strengthen powerband and be all in before limiter. my 04 has small stk. lift web regrinds at 107, 104, leaves hard and plenty of top end at consistent 157 mph quarters. good luck with ur build.
    checkmate likes this.

  4. #18
    Moving up the Ladder
    Steve 10r's Avatar
    Join Date
    Apr 2012
    Location
    Angleton, Texas
    Posts
    122
    Post Thanks / Like
    Real Name
    Stephen
    Rep Power
    3
    Country: United States

    Default

    Quote Originally Posted by gazx10 View Post
    just dyno'd and ran 07 10 with ported head, 08 race int. stk. ex. decked ,015, .050 hg, brock pipe, springs, retainers. very similar to u. degreed cams too high lc, 110 int., 106.5 ex., still climbing on dyno at 12500 rev limiter, soft off the line at the strip. gonna redegree to lower #'s, probably 107 int., 104-105 ex. to strengthen powerband and be all in before limiter. my 04 has small stk. lift web regrinds at 107, 104, leaves hard and plenty of top end at consistent 157 mph quarters. good luck with ur build.
    Thanks man if u don't mined me asking what's your HP with that setup

  5. #19
    Moving up the Ladder
    gazx10's Avatar
    Join Date
    Mar 2010
    Location
    monroe, ga.
    Posts
    570
    Post Thanks / Like
    Real Name
    jim shepard
    Rep Power
    5

    Default

    07 made 180hp on pump gas. 04 made 188 on mr12

  6. #20
    Moving up the Ladder
    Steve 10r's Avatar
    Join Date
    Apr 2012
    Location
    Angleton, Texas
    Posts
    122
    Post Thanks / Like
    Real Name
    Stephen
    Rep Power
    3
    Country: United States

    Default

    Quote Originally Posted by gazx10 View Post
    07 made 180hp on pump gas. 04 made 188 on mr12
    Good #s I'm not to far from that at 176 on pump and that's with just dropping the cams in
    I'd like to see how many more pony's I can pick up from degree the cams

  7. #21
    Moving up the Ladder

    Join Date
    Jan 2009
    Location
    Sheboygan Wisconsin
    Posts
    33
    Post Thanks / Like
    Real Name
    "E"
    Rep Power
    6
    Country: United States

    Default

    Just had mine done. 07 ZX10r 08 race intake cam, stock exhaust cam, carp. springs, decked 0.20, 0.45 head gasket, port/polish. 107/104 (thanks to gazx10). Running MR12 still getting the map set up. HP to be determined.

  8. #22
    Moving up the Ladder
    harold b's Avatar
    Join Date
    Jun 2009
    Posts
    81
    Post Thanks / Like
    Rep Power
    6

    Default

    shinobil what is your suggestion on checking ptv

Similar Threads

  1. cam degree
    By lonnie440 in forum Kawasaki ZX12R-ZX14
    Replies: 13
    Last Post: 01-27-2013, 08:52 PM
  2. Cam degree.
    By 08gixxer1000 in forum 1000's
    Replies: 6
    Last Post: 03-11-2012, 09:46 PM
  3. Cam degree
    By roagixxer in forum 1000's
    Replies: 5
    Last Post: 02-17-2012, 10:39 AM
  4. Cam degree help!!!!!!!!!!!
    By TwsTdGsxR in forum 1000's
    Replies: 5
    Last Post: 03-09-2010, 02:18 PM
  5. 05 zx10 cam degree numbers, please help
    By denn911 in forum 1000's
    Replies: 11
    Last Post: 02-14-2010, 01:11 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.