1Likes
LinkBack URL
About LinkBacksok well after about a year and a half long build finally coming to an end.. the bike is all loaded up to nj to get tuned.
engine built by del
1397 pistons
245 intake cam
stock intake on the exhaust side
ported and polished head done by V&H
V&H single tip exhaust
cut trans
stock clutch
+2 swing arm
powercommander 5
hopefully its over 200 hp cause ill be a lil upset if its not
ill update tonight with some pics and hopefully a video
+ Reply to Thread
Results 1 to 15 of 26
Getting my busa tuned up today FINALLY!
This is a discussion about Getting my busa tuned up today FINALLY! within the Suzuki Hayabusa section, where you will Some say Busa's Dominate; ok well after about a year and a half long build finally coming to an end.. the bike is all loaded up to nj to get tuned. engine built by del 1397 pistons 245 intake
- 11-20-2012, 08:00 AM #1Moving up the Ladder
- Join Date
- Nov 2009
- Location
- old bridge new jersey
- Posts
- 213
- Post Thanks / Like
- Real Name
- mike
- Rep Power
- 4
Getting my busa tuned up today FINALLY!
- Sponsored Links Remove Advertisements
- 11-20-2012, 08:58 AM #2Moving up the Ladder
- Join Date
- May 2010
- Location
- Portage,In
- Posts
- 159
- Post Thanks / Like
- Rep Power
- 4
Ya let us know! I just dynoed my 2 second gen last. Didn't tune though it was supposedly tuned before I got it but it seemed a little lean.
- 11-23-2012, 05:06 PM #3Moving up the Ladder
- Join Date
- May 2010
- Location
- Portage,In
- Posts
- 159
- Post Thanks / Like
- Rep Power
- 4
Well how did it do ??
- 11-23-2012, 07:35 PM #4Moving up the Ladder
- Join Date
- Feb 2008
- Location
- PA
- Posts
- 266
- Post Thanks / Like
- Real Name
- bruno
- Rep Power
- 0
Whos tuning the bike for you??
07 64'' nos busa...BLACKOUT DEATH B 4 DISHONOR FAMILY B4 ALL 70'' NOS BUSA WILDTHANG
- 11-24-2012, 08:12 PM #5Moving up the Ladder
- Join Date
- Nov 2009
- Location
- old bridge new jersey
- Posts
- 213
- Post Thanks / Like
- Real Name
- mike
- Rep Power
- 4
whuddup sorry just been working on the bike to get it ready for tomorow (sunday) well jds cycle tuned it for me it got 190 .. was expecting a lil more but im just happy to be riding it again
- 11-24-2012, 09:18 PM #6Super HoleShot Member
- Join Date
- Jan 2002
- Location
- Round Rock TEXAS
- Posts
- 370
- Post Thanks / Like
- Real Name
- Johnnycheese
- Rep Power
- 0
245 cams are way too small
*Super HoleShot Member
I am faster than you
- 11-25-2012, 11:27 AM #7Moving up the Ladder
- Join Date
- May 2010
- Location
- Portage,In
- Posts
- 159
- Post Thanks / Like
- Rep Power
- 4
Don't get discouraged by Dyno numbers! Let the track decide how it runs!!!
- 11-25-2012, 11:56 AM #8Moving up the Ladder
- Join Date
- Feb 2008
- Location
- PA
- Posts
- 266
- Post Thanks / Like
- Real Name
- bruno
- Rep Power
- 0
I hope that's a cAm grind # and not lift..
Originally Posted by Johnnycheese 
07 64'' nos busa...BLACKOUT DEATH B 4 DISHONOR FAMILY B4 ALL 70'' NOS BUSA WILDTHANG
- 11-27-2012, 09:02 PM #9VIP/DONATOR
- Join Date
- Nov 2003
- Location
- VA
- Posts
- 187
- Post Thanks / Like
- Real Name
- Jr.
- Rep Power
- 0
def need bigger cams should be 220 at least with head and a good open pipe"brock"
- 11-28-2012, 11:22 AM #10Moving up the Ladder
- Join Date
- Nov 2009
- Location
- old bridge new jersey
- Posts
- 213
- Post Thanks / Like
- Real Name
- mike
- Rep Power
- 4
10.2 at 140 .. First time on her in 2 years
- 11-28-2012, 05:38 PM #11Moving up the Ladder
- Join Date
- May 2010
- Location
- Portage,In
- Posts
- 159
- Post Thanks / Like
- Rep Power
- 4
How much do you weigh?
- 11-28-2012, 07:16 PM #12Moving up the Ladder
- Join Date
- Oct 2006
- Location
- Apeldoorn The Netherlands
- Posts
- 428
- Post Thanks / Like
- Rep Power
- 0
It sounds ;way off to me.
Numbers too low for all the parts which are in there.
Maybe cam timing off by 1 tooth
- 11-28-2012, 07:22 PM #13Moving up the Ladder
- Join Date
- Nov 2009
- Location
- old bridge new jersey
- Posts
- 213
- Post Thanks / Like
- Real Name
- mike
- Rep Power
- 4
250 suited?... 60inches... lol a weak clutch and a rusty clutch hand.. lol
- 11-28-2012, 07:24 PM #14Moving up the Ladder
- Join Date
- Nov 2009
- Location
- old bridge new jersey
- Posts
- 213
- Post Thanks / Like
- Real Name
- mike
- Rep Power
- 4
im going this weekend to englishtown for a test n tune.. hopefully ill have my air shifter figured out.
- 11-28-2012, 07:28 PM #15Moving up the Ladder
- Join Date
- Nov 2009
- Location
- old bridge new jersey
- Posts
- 213
- Post Thanks / Like
- Real Name
- mike
- Rep Power
- 4
Reply With QuoteSimilar Threads
-
Finally sat on a 2012 ZX14R today.
By smokinstorm in forum Kawasaki ZX12R-ZX14Replies: 0Last Post: 01-13-2012, 08:03 PM -
540 SAE, 550 STD HP Busa Tuned with ECU Editor
By Rodney Williford in forum Staging LanesReplies: 31Last Post: 04-06-2011, 02:37 PM -
zx14 with gen2 busa ecu being tuned
By stocker in forum Kawasaki ZX12R-ZX14Replies: 20Last Post: 02-11-2011, 11:50 AM -
Dyno tuned the Busa today
By blackclover in forum Suzuki HayabusaReplies: 38Last Post: 07-14-2010, 01:23 PM -
Dyno tuned today- custom map
By 9secondsflat in forum Kawasaki ZX12R-ZX14Replies: 9Last Post: 06-07-2010, 12:27 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.